Processing Properties | Metric | English | Comments |
---|---|---|---|
Cure Time | 45.0 min @Temperature 150 °C |
0.750 hour @Temperature 302 °F |
|
Permabond ES558 Epoxy Resin PERMABOND ES558 is a single-part epoxy paste which flows like solder when heated during curing. The adhesive is toughened for maximum impact resistance, along with excellent peel and shear strength... |
|||
Cure Time | 45.0 min @Temperature 152 °C |
0.750 hour @Temperature 305 °F |
|
TSE Industries Millathane® 5004 Millable Polyurethane Elastomer with 3 PHR Di-Cup 40C MILLATHANE 5004 is a millable polyurethane elastomer having excellent processing characteristics. MILLATHANE 5004 stocks can be readily processed on conventional rubber equipment. Vulcanization is c.. |
|||
Cure Time | 45.0 min @Temperature 152 °C |
0.750 hour @Temperature 305 °F |
|
TSE Industries Millathane® 5004 Millable Polyurethane Elastomer with 8 PHR Di-Cup 40C MILLATHANE 5004 is a millable polyurethane elastomer having excellent processing characteristics. MILLATHANE 5004 stocks can be readily processed on conventional rubber equipment. Vulcanization is c.. |
|||
Cure Time | 45.0 min @Temperature 150 °C |
0.750 hour @Temperature 302 °F |
Oven |
Permabond ES569 Epoxy Resin PERMABOND® ES569 is a single-part heat cured epoxy adhesive with excellent adhesion to metal surfaces as well as composite materials. The high bond strength of this adhesive allows it to replace me.. |
|||
Cure Time | 45.0 - 60.0 min | 0.750 - 1.00 hour | Functional cure |
ITW Devcon 5 minute® Epoxy Gel, Opaque Information provided by ITW Devcon |
|||
Cure Time | 45.0 - 60.0 min | 0.750 - 1.00 hour | Functional cure |
ITW Devcon 5 minute® Epoxy, Light Amber Information provided by ITW Devcon |
|||
Cure Time | 45.0 - 60.0 min | 0.750 - 1.00 hour | Functional cure |
ITW Devcon Composite Welderâ„¢ Methacrylate Adhesive FS, Blue Green, Black Information provided by ITW Devcon |
|||
Cure Time | 45.0 min | 0.750 hour | Tack-free |
Momentive Performance Materials RTV157 High Strength Silicone Adhesive Sealant, Gray RTV 157 is a one component, ready-to-use, high strength silicone rubber adhesive sealant. It cures to tough resilient silicone rubber on exposure to atmospheric moisture at room temperature. RTV15.. |
|||
Cure Time | 45.0 min | 0.750 hour | Tack-free |
Momentive Performance Materials RTV5249 Neutral Cure, One Component RTV Adhesive Sealant RTV5240 series sealants are alkoxy neutral cure, one-component, ready to use, electronic grade silicone adhesive sealants exhibiting high strength that will maintain a strong bond even when exposed .. |
|||
Cure Time | 45.0 min @Temperature 152 °C |
0.750 hour @Temperature 305 °F |
|
TSE Industries Millathane® 5004 Millable Polyurethane Elastomer with 3 PHR Di-Cup 40C MILLATHANE 5004 is a millable polyurethane elastomer having excellent processing characteristics. MILLATHANE 5004 stocks can be readily processed on conventional rubber equipment. Vulcanization is c.. |
|||
Cure Time | 45.0 min @Temperature 152 °C |
0.750 hour @Temperature 305 °F |
|
TSE Industries Millathane® 5004 Millable Polyurethane Elastomer with 4 PHR Di-Cup 40C MILLATHANE 5004 is a millable polyurethane elastomer having excellent processing characteristics. MILLATHANE 5004 stocks can be readily processed on conventional rubber equipment. Vulcanization is c.. |
|||
Cure Time | 45.0 min @Temperature 152 °C |
0.750 hour @Temperature 305 °F |
|
TSE Industries Millathane® 5004 Millable Polyurethane Elastomer with 5 PHR Di-Cup 40C MILLATHANE 5004 is a millable polyurethane elastomer having excellent processing characteristics. MILLATHANE 5004 stocks can be readily processed on conventional rubber equipment. Vulcanization is c.. |
|||
Cure Time | 45.0 min @Temperature 152 °C |
0.750 hour @Temperature 305 °F |
|
TSE Industries Millathane® 5004 Millable Polyurethane Elastomer with 6 PHR Di-Cup 40C MILLATHANE 5004 is a millable polyurethane elastomer having excellent processing characteristics. MILLATHANE 5004 stocks can be readily processed on conventional rubber equipment. Vulcanization is c.. |
|||
Cure Time | >= 45.0 min | >= 0.750 hour | Tack Free Time |
ACC EP AEP EPI Engineered Polymers EP AEP is a new generation of Internetwork Polymers of polyurea and Epoxy, “Powered by Reactamine® Technology”. EP AEP was developed for a colorfast floor for both residential and industrial appl.. |
|||
Cure Time | 45.0 - 60.0 min | 0.750 - 1.00 hour | Tack Free Time, catalyzed with QM CAT RED 3 |
ACC QM 107 QSI Quantum Silicones 7 Durometer Condensation Cure Moldmaking Material QM 107 is a two component, room temperature condensation cure silicone material. The cured rubber is very soft, has excellent mechanical properties and good shelf-life stability. This material is us.. |
|||
Cure Time | 45.0 min @Temperature 232 °C |
0.750 hour @Temperature 450 °F |
Adequate ventilation is required when curing these products. Outgassing will occur above 300°F and cease after 750°F. An additional 30 minutes is required at the highest service temperature if service temperature is below 750°F. |
Aremco Corr-Paint™ CP4050 High Temperature Protective Coating Silicone Low viscosity, green coating for power resistors to 1100°F (593°C) |
|||
Cure Time | 45.0 min @Temperature 249 °C |
0.750 hour @Temperature 480 °F |
|
Aremco Corr-Paint™ CP4060-S High Temperature Protective Coating, Silicone-Polyester |
|||
Cure Time | 45.0 min @Temperature 249 °C |
0.750 hour @Temperature 480 °F |
|
Aremco Corr-Paint™ CP4070-S High Temperature Protective Coating, Silicone-Polyester |
|||
Cure Time | 45.0 min @Temperature 249 °C |
0.750 hour @Temperature 480 °F |
|
Aremco Corr-Paint™ CP4070-S1 High Temperature Protective Coating, Silicone |
|||
Cure Time | 45.0 min @Temperature 249 °C |
0.750 hour @Temperature 480 °F |
|
Aremco Corr-Paint™ CP4080-S High Temperature Protective Coating, Silicone-Polyester |
|||
Cure Time | 45.0 min @Temperature 249 °C |
0.750 hour @Temperature 480 °F |
|
Aremco Corr-Paint™ CP4080-S1 High Temperature Protective Coating, Silicone |
|||
Cure Time | 45.0 min @Temperature 249 °C |
0.750 hour @Temperature 480 °F |
|
Aremco Corr-Paint™ CP4090 High Temperature Protective Coating Silicone, Aluminum Filled This silicone-based, heat resistant coatings are formulated using a state-of-the-art, VOC-compliant, water-dispersible silicone resin. CP4000 adheres to metals, ceramics, refractories, and quartz, a.. |
|||
Cure Time | 45.0 min @Temperature 249 °C |
0.750 hour @Temperature 480 °F |
|
Aremco Corr-Paint™ CP4090-S1 High Temperature Protective Coating, Silicone |
|||
Cure Time | 45.0 min @Temperature 249 °C |
0.750 hour @Temperature 480 °F |
|
Aremco Corr-Paint™ CP4020 High Temperature Protective Coating Silicone, Aluminum Filled This silicone-based, heat resistant coatings are formulated using a state-of-the-art, VOC-compliant, water-dispersible silicone resin. CP4010 adheres to metals, ceramics, refractories, and quartz, a.. |
|||
Cure Time | 45.0 min @Temperature 249 °C |
0.750 hour @Temperature 480 °F |
|
Aremco Corr-Paint™ CP4020-S1 High Temperature Protective Coating, Silicone |
|||
Cure Time | 45.0 min @Temperature 249 °C |
0.750 hour @Temperature 480 °F |
|
Aremco Corr-Paint™ CP4090-S High Temperature Protective Coating, Silicone-Polyester |
|||
Cure Time | 45.0 min @Temperature 249 °C |
0.750 hour @Temperature 480 °F |
|
Aremco Corr-Paint™ CP4095 High Temperature Protective Coating Silicone, Aluminum Filled This silicone-based, heat resistant coatings are formulated using a state-of-the-art, VOC-compliant, water-dispersible silicone resin. CP4000 adheres to metals, ceramics, refractories, and quartz, a.. |
|||
Cure Time | 45.0 min @Temperature 152 °C |
0.750 hour @Temperature 305 °F |
|
TSE Industries Millathane® 5004 Millable Polyurethane Elastomer, Hardness 70A MILLATHANE 5004 is a millable polyurethane elastomer having excellent processing characteristics. MILLATHANE 5004 stocks can be readily processed on conventional rubber equipment. Vulcanization is c.. |
|||
Cure Time | 45.0 min @Temperature 152 °C |
0.750 hour @Temperature 305 °F |
|
TSE Industries Millathane® 5004 Millable Polyurethane Elastomer with 5 PHR Di-Cup 40C MILLATHANE 5004 is a millable polyurethane elastomer having excellent processing characteristics. MILLATHANE 5004 stocks can be readily processed on conventional rubber equipment. Vulcanization is c.. |