Processing Properties | Metric | English | Comments |
---|---|---|---|
Cure Time | 1440 min | 24.0 hour | On Steel (Full) |
ND Industries 567 Shaft & Bearing Retainer Retaining Compound High temperature retainer for engine cylinder liners and heat exchanger tubes |
|||
Cure Time | 1440 min | 24.0 hour | On steel (Full) |
ND Industries StudGrade® 131 Permanent CT Threadlocker General DescriptionHigh strength threadlockers for maximum security. Suitable for most applications where disassembly is not required.Typical Usesstuds and bolts, and threaded pipe fittings.Meets m.. |
|||
Cure Time | 1440 min | 24.0 hour | full cure |
Permabond TA4302 Toughened Acrylic Adhesive PERMABOND® TA4302 is a 2-part, 1:1 toughened acrylic adhesive. It can be used to bond a wide variety of materials including metals, plastics, GRP, ceramics, wood and other substrates. It is conveni.. |
|||
Cure Time | 1440 - 2880 min | 24.0 - 48.0 hour | hard dry (return to service) |
Industrial Nanotech Nansulateâ„¢ GP Translucent Insulation Coating Liquid insulation and corrosion protection incorporating Hydro-NM-Oxide, a product of nanotechnology. This grade is for general purpose insulation.NANSULATEâ„¢ liquid applied insulation is a prem.. |
|||
Cure Time | 1440 min | 24.0 hour | Functional cure |
ITW Devcon Epoxy HP 250, Straw Information provided by ITW Devcon |
|||
Cure Time | <= 1440 min | <= 24.0 hour | Curing |
Silikony Polskie Gumosil B Silicone Rubber Flexible with low hardness |
|||
Cure Time | 1440 - 2880 min @Temperature 23.0 °C |
24.0 - 48.0 hour @Temperature 73.4 °F |
|
Master Bond Mastersil 701 One Component, Room Temperature Curing Silicone Elastomer Master Bond Master Sil 701 is a ready-to-use, one component, high performance silicone elastomer compound for bonding, and sealing protective coatings and formed-in-place gaskets. It cures at ambien.. |
|||
Cure Time | 1440 min @Temperature 25.0 °C |
24.0 hour @Temperature 77.0 °F |
|
Tra-Con Tra-Bond 2114 Water White Transparent Epoxy Adhesive TRA-BOND 2114 is a transparent, low viscosity epoxy resin formulation recommended for industrial adhesive and laminating applications where sparkling clarity and excellent structural, mechanical and.. |
|||
Cure Time | 1440 min @Temperature 25.0 °C |
24.0 hour @Temperature 77.0 °F |
|
Tra-Con Tra-Bond 216H02 Opaque Black Epoxy Casting Compound TRA-CAST 216H02 is a medium viscosity two-part formulation recommended for general purpose electrical potting and encapsulation applications where the combination of good mechanical thermal and elec.. |
|||
Cure Time | 1440 min | 24.0 hour | Full Cure; Varies with substrates |
Loctite® PRISM® 4212 Instant Adhesive Gel Cyanoacrylate Bonding AdhesivesLoctite® technology has made the productivity promises of cyanoacrylate adhesives a reality with the industry's widest selection of high-performance, application-.. |
|||
Cure Time | 1440 min | 24.0 hour | Full Cure; Varies with substrates |
Loctite® Quick Set™ 404 Industrial Adhesive Cyanoacrylate Bonding AdhesivesLoctite® technology has made the productivity promises of cyanoacrylate adhesives a reality with the industry's widest selection of high-performance, application-.. |
|||
Cure Time | 1440 min @Temperature 25.0 °C |
24.0 hour @Temperature 77.0 °F |
|
Cytec (Conap) RN-1000 / EA-87 Conapoxy® Resin / Conacure® Hardener Epoxy Potting and Encapsulating Systems for Electronic ApplicationsHigh technology epoxy resin systems for potting and encapsulation, for the defense, aerospace, electronics, computer, automotive an.. |
|||
Cure Time | 1440 min @Temperature 25.0 °C |
24.0 hour @Temperature 77.0 °F |
|
Cytec (Conap) RN-1210 / EA-02 Conapoxy® Resin / Conacure® Hardener Epoxy Potting and Encapsulating Systems for Electronic ApplicationsHigh technology epoxy resin systems for potting and encapsulation, for the defense, aerospace, electronics, computer, automotive an.. |
|||
Cure Time | 1440 min @Temperature 25.0 °C |
24.0 hour @Temperature 77.0 °F |
|
Cytec (Conap) RN-1210 / EA-028 Conapoxy® Resin / Conacure® Hardener Epoxy Potting and Encapsulating Systems for Electronic ApplicationsHigh technology epoxy resin systems for potting and encapsulation, for the defense, aerospace, electronics, computer, automotive an.. |
|||
Cure Time | 1440 min @Temperature 22.0 °C |
24.0 hour @Temperature 71.6 °F |
|
Dow Corning 236 DISPERSION Flowable (as supplied) silicone RTV coatingInformation provided by Dow Corning |
|||
Cure Time | 1440 - 4320 min | 24.0 - 72.0 hour | (1-3 Days) |
Abatron AboWeld 8104-12 Polysulfide-Epoxy Sealant and Caulk AboWeld 8104-12 is a 2-part, 100% solids, liquid or filled polysulfide-epoxy. It is available in many colors. It is often used with sand and gravel to mix grouts for filling and resurfacing. It is p.. |
|||
Cure Time | 1440 min | 24.0 hour | Tack-Free Time |
3M AC-645 B-2 Aerospace Sealant 3M Aerospace Sealant AC-645 B-2 is a low density, two-component, manganese dioxide cured, liquid polysulfide polymer system. It is suitable for use in fuel tanks, fuselage hole filling, cavity filli.. |
|||
Cure Time | 1440 min | 24.0 hour | |
3M AC-645 B-2 Aerospace Sealant 3M Aerospace Sealant AC-645 B-2 is a low density, two-component, manganese dioxide cured, liquid polysulfide polymer system. It is suitable for use in fuel tanks, fuselage hole filling, cavity filli.. |
|||
Cure Time | 1440 min | 24.0 hour | Full Cure |
3M Scotch-Weld™ GM18 Gasket Maker Anaerobic Adhesive 3M™ Scotch-Weld™ Gasket Maker Anaerobic Adhesives are one-component anaerobic sealants formulated to replace pre-cut gaskets or used as form-in-place gaskets that cure at room temperature and seal.. |
|||
Cure Time | 1440 min | 24.0 hour | heavy duty use |
3M 32660 Heavy Duty Performance Coating - Part A 3M™ HD (Heavy Duty) Performance Coating is 100% solids elastomeric lining especially developed for high abrasion and tear resistance with thick build up characteristics. It has good durability and .. |
|||
Cure Time | 1440 min | 24.0 hour | heavy duty use |
3M 32666 Tan Heavy Duty Performance Coating - Part B 3M™ HD (Heavy Duty) Performance Coating is 100% solids elastomeric lining especially developed for high abrasion and tear resistance with thick build up characteristics. It has good durability and .. |
|||
Cure Time | 1440 min | 24.0 hour | Rate of Cure, 50% RH |
3M 551 Polyurethane Adhesive Sealant 3M™ 500-Series Polyurethane Construction Sealant, Polyurethane Sealant and Polyurethane Adhesive Sealant products are one component, moisture curing products which form permanent elastic bonds. The.. |
|||
Cure Time | 1440 min | 24.0 hour | Rate of Cure, 50% RH |
3M 560 Polyurethane Adhesive Sealant 3M™ 500-Series Polyurethane Construction Sealant, Polyurethane Sealant and Polyurethane Adhesive Sealant products are one component, moisture curing products which form permanent elastic bonds. The.. |
|||
Cure Time | 1440 min @Temperature 24.0 °C |
24.0 hour @Temperature 75.2 °F |
|
BCC Products HPX-850 Epoxy Backfill System HPX-850 is a light weight, heat resistant, two component epoxy backfill system. HPX-850 features advantages such as low cost, long pot life, machineability, and low shrinkage. HPX-850 is ideally su.. |
|||
Cure Time | 1440 min | 24.0 hour | Tack-Free Time |
3M AC-730 Class C-8 (24) Aerospace Sealant 3M Aerospace Sealant AC-730 Class C are two-part, manganese-cured, non-chromate corrosion inhabiting sealants. These Sealants provide an effective barrier against the common causes of corrosion on a.. |
|||
Cure Time | 1440 min | 24.0 hour | Full Cure, 50% RH, 1/8" depth |
3M PN8029 Marine Grade Silicone Sealant A mildew resistant, non-sagging, moisture curing silicone rubber sealant for above the waterline applications which remains flexible with excellent resistance to the marine environment. Adheres to b.. |
|||
Cure Time | 1440 min | 24.0 hour | |
3M Scotch-Weld™ RT80 Retaining Compound Anaerobic Adhesives 3M™ Scotch-Weld™ Retaining Compound Anaerobic Adhesives are one-component anaerobic adhesives designed to secure cylindrical metal assemblies such as bearings on shafts, bushing, sleeves, housings.. |
|||
Cure Time | 1440 min | 24.0 hour | Full Cure; Varies with substrates |
Loctite® Ultra Grey® 5699 Flange Sealant Silicone GasketingLoctite® Silicone Gasketing materials include unique products with excellent resistance, formulations for high operating temperatures, and UV-curing formulations for cure-in-place.. |
|||
Cure Time | 1440 min @Temperature 25.0 °C |
24.0 hour @Temperature 77.0 °F |
Full Cure; Steel |
Loctite® Quick Metal® 660 Retaining Compound RetainersLoctite Corporation, the pioneer of anaerobic adhesives, has applied this technology to create retaining compounds that increase the shear strength of cylindrical, non-threaded assemblies. .. |