Mechanical Properties | Metric | English | Comments |
---|---|---|---|
Tensile Strength, Ultimate | >= 550 MPa | >= 79800 psi | EN 10002-1 |
Outokumpu 4311 Cr-Ni Austenitic Stainless Steel Applications: Wet corrosion resistance and general service.Available in hot rolled plate (Quarto), hot rolled strip/sheet (CPP), cold rolled strip/sheet, cold rolled narrow strip, bar, and rod forms.. |
|||
Tensile Strength, Ultimate | 550 MPa | 79800 psi | ASTM D638 |
Owens Corning Glass Fiber Reinforced Epoxy (Filament Wound), 80 wt.% glass Epoxies are highly resistant to water, alkalis and organic solvents. Although standard epoxies have only a fair resistance to acids and oxidizing agents, they can be formulated for better resistance.. |
|||
Tensile Strength, Ultimate | >= 550 MPa | >= 79800 psi | |
MetalTek Copper Ni Si Cast UNS C81540 High Conductivity Information provided by MetalTekCast Grade C81540 |
|||
Tensile Strength, Ultimate | >= 550 MPa | >= 79800 psi | |
MetalTek MTEK CE20N Cast UNS N08007 Austenitic Stainless Steel "300" series, general corrosion resistant alloyApplications: Nuclear, chemical and food processing. Valve and pump trim.Information provided by MetalTekCast UNS N08007; Cast Grade CE20N; Cast ASTM A.. |
|||
Tensile Strength, Ultimate | >= 550 MPa | >= 79800 psi | |
MetalTek MTEK N155 UNS R30155 Severe Corrosion and Heat Resistant Alloy Information provided by MetalTek |
|||
Tensile Strength, Ultimate | 550 MPa | 79800 psi | Typical after Solution Annealing |
Industeel SIRIUS 310 25% Cr - 0.6% Si Heat Resistant Stainless Steel Description: CLI SIRIUS 310 grade is a fully austenitic stainless steel containing 25% Cr, 0.6% Si and 20% Ni additions. The alloy is well known for its multi-purpose high temperature corrosion resi.. |
|||
Tensile Strength, Ultimate | >= 550 MPa | >= 79800 psi | |
MetalTek 254 SMO® Super Austenitic Stainless Steel Corrosion resistance approaching nickel alloys, especially in chloride service. Produced under license of Avesta Jernverk AB. Applications: Process piping exposed to flue gas and solutions.Informati.. |
|||
Tensile Strength, Ultimate | >= 550 MPa | >= 79800 psi | |
MetalTek MTEK 25-12 TYPE II Cast UNS J93303 Heat Resistant Stainless Steel Very sensitive to composition balance. Suitable for a wide range of high temperature applications.Applications: Rable arms, radiant tubes, refractory support hardware, grate bars.Information provide.. |
|||
Tensile Strength, Ultimate | >= 550 MPa | >= 79800 psi | |
MetalTek MTEK 6XN Cast UNS J94651 Super Austenitic Stainless Steel Corrosion resistance approaching nickel alloys, especially in chloride service.Applications: Process piping exposed to flue gas and solutions.Information provided by MetalTek |
|||
Tensile Strength, Ultimate | 550 MPa | 79800 psi | Annealed |
Special Metals MONEL® Alloy 400 A nickel-copper alloy with high strength and excellent corrosion resistance in a range of media including sea water, hydrofluoric acid, sulfuric acid, and alkalis. Used for marine engineering, chem.. |
|||
Tensile Strength, Ultimate | 550 - 700 MPa | 79800 - 102000 psi | |
SSAB Tunnplat Domex® 500MC HSLA Steel HSLA SteelCharacteristics: Some thicknesses of these steel grades are available with a maximum of 0.03% Si for thin Zn coating. If the material is to be hot-dip galvanized and steel with a maximum .. |
|||
Tensile Strength, Ultimate | 550 MPa | 79800 psi | |
Wieland 1408 Wilaform Gold Hard yellow gold alloy. Easily splintered and polished.Applications: casting, laminar decoration, tubingDental |
|||
Tensile Strength, Ultimate | 550 - 610 MPa | 79800 - 88500 psi | Wire |
CLAL-MSX ARCAP Anticorrosion AP1 H13 3/4 hard, Drawn Copper Alloy Description: The AP1D grade has been developed especially for being machined by lathe. The very good machineability of the AP1D grade may be summerised by: cutting speed up to 150 m/minute (accordin.. |
|||
Tensile Strength, Ultimate | 550 - 600 MPa | 79800 - 87000 psi | Rod |
CLAL-MSX ARCAP Anticorrosion AP1 H14 4/4 hard, Drawn Copper Alloy Description: The AP1D grade has been developed especially for being machined by lathe. The very good machineability of the AP1D grade may be summerised by: cutting speed up to 150 m/minute (accordin.. |
|||
Tensile Strength, Ultimate | <= 550 MPa | <= 79800 psi | Wire |
CLAL-MSX ARCAP Anticorrosion AP4 0 Annealed, Drawn Copper Alloy Description: The AP4 grade is less easy to turn than the other grades of ARCAP. It can however be machined without more difficulty than the nickel chromium molybdenum steels.High Corrosion Resistanc.. |
|||
Tensile Strength, Ultimate | 550 - 650 MPa | 79800 - 94300 psi | Wire |
CLAL-MSX ARCAP Anticorrosion AP4 H11 1/4 hard, Drawn Copper Alloy Description: The AP4 grade is less easy to turn than the other grades of ARCAP. It can however be machined without more difficulty than the nickel chromium molybdenum steels.High Corrosion Resistanc.. |
|||
Tensile Strength, Ultimate | 550 - 600 MPa | 79800 - 87000 psi | Rod |
CLAL-MSX ARCAP Anticorrosion AP4 H12 1/2 hard, Drawn Copper Alloy Description: The AP4 grade is less easy to turn than the other grades of ARCAP. It can however be machined without more difficulty than the nickel chromium molybdenum steels.High Corrosion Resistanc.. |
|||
Tensile Strength, Ultimate | 550 MPa | 79800 psi | As Cast |
AFE Technologies Cronite 25Cr/12Ni No. HR7 High temperature nickel alloy castings. Applications include heat treatment and handling products, furnace products, tubes, power generation, and petrochemical industries.Information provided by AF.. |
|||
Tensile Strength, Ultimate | 550 MPa | 79800 psi | |
Ametek P434L P/M Stainless Steel, Sintered from 7.0 g/cc Green Density >Powder apparent bulk density 2.8 g/cc; powder flow 30 sec/50g.Compacting properties measured on powders with 1% lithium stearite. Sintering was done in dissociated ammonia at 1121°C (2050°F) for.. |
|||
Tensile Strength, Ultimate | 550 - 650 MPa | 79800 - 94300 psi | |
ArcelorMittal HSLA 460 High strength low alloy steel for cold forming, Hot Rolled Available in the following: S460MCDescription: Steels in the HSLA (High Strength Low Alloy) range are hardened by a combination of precipitation and grain size refining, resulting in high strength w.. |
|||
Tensile Strength, Ultimate | 550 MPa | 79800 psi | Typical after Solution Annealing |
Industeel UREA 25.22.2 Plants Description: CLI UREA 25.22.2 chemical composition has been optimized for specific uses in Urea plants. It is a 310L modified austenitic stainless steel with low carbon, low silicon and high nitroge.. |