- HOME
- POLYMER SEARCH
- Polymer Property : Maximum Service Temperature, Air = 200 °C
Polymer Property : Maximum Service Temperature, Air = 200 °C Product List
Thermal PropertiesTips: 30 items are displayed at most.
| Thermal Properties | Metric | English | Comments |
|---|---|---|---|
| Maximum Service Temperature, Air | 200 °C | 392 °F | Recommended |
|
Nye Lubricants 741B (NG) Synthetic Oil
Information provided by Nye Lubricants.
|
|||
| Maximum Service Temperature, Air | 200 °C | 392 °F | |
|
Precision Polymer Engineering V85F Fluoroelastomer Compound
Special steam resistant, Fluoroelastomer Rubber, 80-90 °IRHD. Tetrapolymer of vinylidene fluoride, hexafluoropropylene and tetrafluoroethylene and cure site monomer (CSM). To meet ASTM D2000 line c..
|
|||
| Maximum Service Temperature, Air | 200 °C | 392 °F | Recommended |
|
Nye Lubricants 854J-MS (FG) Synthetic Oil
Information provided by Nye Lubricants.
|
|||
| Maximum Service Temperature, Air | 200 °C | 392 °F | |
|
Precision Polymer Engineering V65B Fluoroelastomer Compound
Fluoroelastomer Rubber, 61-70 °IRHD. Copolymer of vinylidene fluoride and hexafluoropropylene.Applications: Excellent resistance to oils, fuels and hydraulic fluids at high temperature.
|
|||
| Maximum Service Temperature, Air |
200
°C @Time >=1200 sec |
392
°F @Time >=0.333 hour |
|
|
Kazanorgsintez 271-274K Cable Composition Based on High Density Polyethylene
Production Method: Gaseous-phase method. Application: Compositions are intended for cover insulating lapping, protective covers and cables.Information Provided by Kazanorgsintez
|
|||
| Maximum Service Temperature, Air | 200 °C | 392 °F | |
|
Möller Medical NanoSkin 75 NanoCoating
Non-abrasive coating with extreme chemical resistance, also applicable for plastics substrates.Information provided by Möller Medical, Member of CENTROTEC Group
|
|||
| Maximum Service Temperature, Air | 200 °C | 392 °F | |
|
Möller Medical NanoSkin 78 NanoCoating
Transparent, scratch-resistant coating also for plastics with good resistance against dissolvents.Information provided by Möller Medical, Member of CENTROTEC Group
|
|||
| Maximum Service Temperature, Air | 200 °C | 392 °F | |
|
Möller Medical PolySkin 82 NanoCoating
Flexible, very non-abrasive, chemical-resistant decorative coating.Information provided by Möller Medical, Member of CENTROTEC Group
|
|||
| Maximum Service Temperature, Air | 200 °C | 392 °F | short term |
|
Lehmann & Voss LUVOCOM® 1100/GF/30/NAT Polyether sulfone, with glass fiber
Applications: Apparatus- and precision engineering, film- and photo industry, sporting- and leisure goods, medical- and electrical enineering, aircraft- and aerospace industry.High dimensionally sta..
|
|||
| Maximum Service Temperature, Air | 200 °C | 392 °F | Short peaks operation |
|
Polyram PlusTek PB304G7 Nylon 6, 35% Glass Fiber
35% glass-fiber reinforced, heat stabilized and impact modified polyamide 6 for injection molding applicationsInformation provided by Polyram Ram On Ind.
|
|||
| Maximum Service Temperature, Air | 200 °C | 392 °F | Short peaks operation |
|
Polyram PlusTek PB315G33 Nylon 6 for Injection Molding, 33% Glass Fiber Reinforced, UV and Heat Stabilized
33% Glass fiber reinforced, UV and heat stabilized Nylon 6 for injection molding applications.Information provided by Polyram.
|
|||
| Maximum Service Temperature, Air | 200 °C | 392 °F | |
|
Dow Corning SE 4448 CV KIT PARTS A&B
Excellent thermal conductivity, low volatility (D4-D10 0.03% wt), heat cure, high viscosity.Information provided by Dow Corning
|
|||
| Maximum Service Temperature, Air | 200 °C | 392 °F | short term; EMS |
|
EMS-Grivory Grivory® TSS/4 LF 2 PA666
Product description: Grilon TSS/4 LF 2 is a heat stabilized, normal viscosity PA66 + PA6 injection molding grade with 2% lubricant (molybdenum disulphide). Grilon TSS/4 LF 2 has the following import..
|
|||
| Maximum Service Temperature, Air | 200 °C | 392 °F | Continuous |
|
Epoxy Technology EPO-TEK® 301 Spectrally Transparent Epoxy
Product Description: EPO-TEK® 301 is a two component, room temperature curing epoxy featuring very low viscosity, and excellent optical-mechanical properties.Advantages & Application Notes: Semicon..
|
|||
| Maximum Service Temperature, Air | 200 °C | 392 °F | Continuous |
|
Epoxy Technology EPO-TEK® 301-2 Optically Transparent Epoxy
Product Description: EPO-TEK® 301-2 is a two component optical, medical, and semiconductor grade epoxy resin, with low viscosity, long pot-life, and good handling characteristics.Advantages & Appli..
|
|||
| Maximum Service Temperature, Air | 200 °C | 392 °F | Continuous |
|
Epoxy Technology EPO-TEK® M10-D Epoxy Paste
Material Description: A single component, B-stageable epoxy paste for semiconductor, microelectronics, and optical assemblies. It can be used in hybrid assemblies for lid-sealing and substrate atta..
|
|||
| Maximum Service Temperature, Air | 200 °C | 392 °F | |
|
Dow Corning 3-6635 DIELECTRIC GEL
One-part, heat cure, with low temperature (-80°C/-112°F) stability.Information provided by Dow Corning
|
|||
| Maximum Service Temperature, Air | 200 °C | 392 °F | Mechanical per UL Card E54153 |
|
Arlon 0.015" (0.381 mm) Flexible Heater Silicone with Fiberglass Substrate (51576R015)
Cured silicone rubber with a minimum thickness of 0.002 in. (0.05 mm)/ 0.008 in. (0.2 mm) Prime Coated 7628 Fiberglass/Uncured silicone rubber with a minimum thickness of 0.005 in. (0.1 mm); 0.003 i..
|
|||
| Maximum Service Temperature, Air | 200 °C | 392 °F | |
|
BASF Ultramid® B3G8 BK00564 40% Glass Filled PA6 (Conditioned)
Ultramid B3G8 BK00564 is a 40% glass filled, pigmented black, injection molding PA6 grade.
|
|||
| Maximum Service Temperature, Air | >= 200 °C | >= 392 °F | 2 hours |
|
Amity Thermosets ATI 172 Phenolic Molding Organic and inorganic Filler, Injection Molded
Characteristics:Heat resistant ( asbestos free )Good electric insulationLow shrinkageLow water absorptionMedium mechanical strengthNot suitable for high mechanical tensionColor-blackVery soft flow ..
|
|||
| Maximum Service Temperature, Air | 200 °C | 392 °F | rated per UL card E54153 |
|
Arlon 30580R020 0.020" (0.508 mm) Uncured Unsupported Silicone Rubber on Kodacel Carrier
Design/Construction:Side 1: Uncured Unsupported Silicone Rubber on Kodacel CarrierAppearance: Red silicone gum on polymer linerThis data represents typical values for the production material. The da..
|
|||
| Maximum Service Temperature, Air | 200 °C | 392 °F | Recommended |
|
Nye Lubricants UniFlor 8921S (UF) Synthetic Oil
Information provided by Nye Lubricants.
|
|||
| Maximum Service Temperature, Air | 200 °C | 392 °F | |
|
Trelleborg S862 Silicone Rubber
PropertiesExcellent resistance to heat (dry air), at +200°C continuous and +220°C intermittent.Remains flexible at low temperatures of -70°C.Resistant to ultra-violet light, ozone and weathering...
|
|||
| Maximum Service Temperature, Air | 200 °C | 392 °F | |
|
Precision Polymer Engineering V60V Fluoroelastomer Compound
Special steam resistant, Black Fluoroelastomer Rubber, 55-65 °IRHD. Terpolymer of vinylidene fluoride, hexafluoropropylene and tetrafluoroethylene. To meet ASTM D2000 line call-out: MHK610, A1-10..
|
|||
| Maximum Service Temperature, Air | 200 °C | 392 °F | |
|
BASF Ultramid® B3UGM210 GR 22866 10/50% Glass/Mineral Filled PA6 FR (Conditioned)
Description: Halogen- and phosphorus-free injection-molding grade with very high rigidity, low smoke density and outstanding electrical properties.Information provided by BASF
|
|||
Copyright © lookpolymers.com All Rights Reserved