Quadrant EPP Duratron® PAI T5530 PAI, 30% glass fibers, compression moulded (ISO Data)

Category	Polymer , Thermoplastic , Polyamide-imide (PAI) , Polyamide-Imide, Glass Filled
Manufacturer	Quadrant Engineering Plastics Products
Trade Name	Duratron® PAI
Port	Shanghai port,China
Trade Terms	FOB, CFR, CIF
Payment Terms	L/C, T/T, Western Union
Download PDF	Quadrant EPP Duratron® PAI T5530 PAI, 30% glass fibers, compression moulded (ISO Data).pdf
Price	EMAIL US sales@lookpolymers.com

Material Notes:

This 30 % glass fibre reinforced grade offers higher stiffness, strength and creep resistance than the Duratron PAI grades mentioned above. It is well suited for structural applications supporting static loads for long periods of time at high temperatures. In addition, Duratron T5530 PAI exhibits superb dimensional stability up to 250 °C making it extremely popular for precision parts in e.g. the electronical and semiconductor industries. The suitability of Duratron T5530 PAI for sliding parts, however, is to be carefully examined since the glass fibres tend to abrade the mating surface. Very high maximum allowable service temperature in air (250°C continuously) Excellent retention of mechanical strength, stiffness and creep resistance over a wide temperature range Dimensional stability up to 260°C Excellent wear & frictional behaviour (particulary Duratron T4301 & T4501 PAI) Very good UV-resistanceGood resistance against high energy radiation (gamma- and X-rays) Inherent low flammability

Physical Properties	Metric	English	Comments
Density	1.61 g/cc	0.0582 lb/in³	ISO 1183-1
Moisture Absorption at Equilibrium	1.7 %	1.7 %	50% RH
Water Absorption at Saturation	3.2 %	3.2 %

Mechanical Properties	Metric	English	Comments
Hardness, Rockwell E	85	85	ISO 2039-2
Hardness, Shore D	90	90
Ball Indentation Hardness	275 MPa	39900 psi	ISO 2039-1
Tensile Strength	125 MPa	18100 psi	at Break (NYP); ISO 527-1/-2
Elongation at Break	3.0 %	3.0 %	ISO 527-1/-2
Tensile Modulus	6.40 GPa	928 ksi	ISO 527-1/-2
Flexural Strength	170 MPa	24700 psi
Compressive Strength	55.0 MPa @Strain 1 %	7980 psi @Strain 1 %	ISO 604
	104 MPa @Strain 2 %	15100 psi @Strain 2 %	ISO 604
	190 MPa @Strain 5 %	27600 psi @Strain 5 %	ISO 604
Charpy Impact Unnotched	3.00 J/cm²	14.3 ft-lb/in²	ISO 179-1/1eU
Charpy Impact, Notched	0.350 J/cm²	1.67 ft-lb/in²	ISO 179-1/1eA
Coefficient of Friction, Dynamic	0.35 - 0.60	0.35 - 0.60

Thermal Properties	Metric	English	Comments
CTE, linear	35.0 µm/m-°C @Temperature 23.0 - 100 °C	19.4 µin/in-°F @Temperature 73.4 - 212 °F
Thermal Conductivity	0.360 W/m-K	2.50 BTU-in/hr-ft²-°F
Maximum Service Temperature, Air	250 °C	482 °F	Continuous
Deflection Temperature at 1.8 MPa (264 psi)	280 °C	536 °F	ISO 75-1/-2
Glass Transition Temp, Tg	280 °C	536 °F	DSC, 20°C/min.; ISO 11357-1/-2
Flammability, UL94	V-0	V-0
Oxygen Index	50 %	50 %	ISO 4589-1/-2

Electrical Properties	Metric	English	Comments
Volume Resistivity	>= 1.0e+14 ohm-cm	>= 1.0e+14 ohm-cm	IEC 60093
Surface Resistivity per Square	>= 1.0e+13 ohm	>= 1.0e+13 ohm	IEC 60093
Dielectric Constant	4.4 @Frequency >=100000 Hz	4.4 @Frequency >=100000 Hz	IEC 60250
Dielectric Strength	28.0 kV/mm	711 kV/in
Dissipation Factor	0.022 @Frequency 100000 Hz	0.022 @Frequency 100000 Hz	IEC 60250
Comparative Tracking Index	175 V	175 V	IEC 60112

Compliance Properties	Metric	English
3A-Dairy	No	No
European Food 1935/2004	No	No
FDA	No	No
USP Class VI	No	No

Chemical Resistance Properties	Metric	English
Acids, Strong (pH 1-3)	Limited	Limited
Acids, Weak	Acceptable	Acceptable
Alcohols	Acceptable	Acceptable
Alkalies, Strong (pH 11-14)	Unacceptable	Unacceptable
Alkalies, Weak	Limited	Limited
Chlorinated Solvents	Acceptable	Acceptable
Continuous Sunlight	Limited	Limited
Hot Water / Steam	Limited	Limited
Hydrocarbons - Aliphatic	Acceptable	Acceptable
Hydrocarbons - Aromatic	Acceptable	Acceptable
Inorganic Salt Solutions	Acceptable	Acceptable
Ketones, Esters	Acceptable	Acceptable

Users viewing this material also viewed the following: