- HOME
- POLYMER SEARCH
- Thermoplastic
- Polyphenylsulfone (PPSU)
- GEHR Plastics PPSU Polyphenylenesulfone
GEHR Plastics PPSU Polyphenylenesulfone
| Category | Polymer , Thermoplastic , Polyphenylsulfone (PPSU) |
| Manufacturer | GEHR Plastics Inc |
| Trade Name | |
| Port | Ningbo port,China |
| Trade Terms | FOB, CFR, CIF |
| Payment Terms | L/C, T/T, Western Union |
| Download PDF | GEHR Plastics PPSU Polyphenylenesulfone.pdf  |
| Price | EMAIL US sales@lookpolymers.com |
Material Notes:
Polyphenylenesulfone is an amorphous material, with improved impact and hydrolysis resistance compared to PSU. The usual operating temperature is approximately 180°C. The extremely high notched impact strength remains also after a heat aging.Propertieshigh strength and rigidityvery high impact strengthvery good dimensional stabilityvery high chemical resistancehigh resistance to all kinds of radiationrepeated sterilizationlower chemical resistance than comparable semi-crystalline materialsApplications include parts for microwave ovens, blow dryers, parts for humidifiers, food industry, pump wheels, insulators, and medical industry.
| Physical Properties | Metric | English | Comments |
|---|---|---|---|
| Specific Gravity | 1.29 g/cc | 1.29 g/cc | ISO 1183 |
| Water Absorption | 0.40 % | 0.40 % | ISO 62 |
| Mechanical Properties | Metric | English | Comments |
|---|---|---|---|
| Hardness, Rockwell R | 122 | 122 | |
| Hardness, Shore D | 86 | 86 | DIN 53505 |
| Tensile Strength, Yield | 70.0 MPa | 10200 psi | ISO 527 |
| Elongation at Break | >= 50 % | >= 50 % | ISO 527 |
| Elongation at Yield | 7.2 % | 7.2 % | ISO 527 |
| Modulus of Elasticity | 2.34 GPa | 339 ksi | ISO 527 |
| Flexural Strength | 105 MPa | 15200 psi | 3.5%; ISO 178 |
| Thermal Properties | Metric | English | Comments |
|---|---|---|---|
| CTE, linear | 56.0 µm/m-°C @Temperature 20.0 °C |
31.1 µin/in-°F @Temperature 68.0 °F |
DIN 53752 |
| Thermal Conductivity | 0.300 W/m-K | 2.08 BTU-in/hr-ft²-°F | DIN 52612 |
| Maximum Service Temperature, Air | 180 °C | 356 °F | |
| Deflection Temperature at 0.46 MPa (66 psi) | 214 °C | 417 °F | ISO 75 |
| Deflection Temperature at 1.8 MPa (264 psi) | 207 °C | 405 °F | ISO 75 |
| Minimum Service Temperature, Air | -50.0 °C | -58.0 °F | |
| Flammability, UL94 | V-0 | V-0 |
| Electrical Properties | Metric | English | Comments |
|---|---|---|---|
| Volume Resistivity | >= 1.00e+15 ohm-cm | >= 1.00e+15 ohm-cm | VDE 0303 |
| Surface Resistivity per Square | >= 1.00e+13 ohm | >= 1.00e+13 ohm | VDE 0303 |
| Dielectric Constant | 3.4 @Frequency 1.00e+6 Hz |
3.4 @Frequency 1.00e+6 Hz |
DIN 53483 |
| Dielectric Strength | 15.0 kV/mm | 381 kV/in | VDE 0303 |
| Dielectric Loss Index | 0.0080 @Frequency 1.00e+6 Hz |
0.0080 @Frequency 1.00e+6 Hz |
DIN 53483 |
| Descriptive Properties | Value | Comments |
|---|---|---|
| Acid Resistance | yes | |
| Aromatic Resistance | yes | |
| Bondability | yes | |
| CKW Resistance | limited | |
| Color | Black | |
| Hydrocarbonate Resistance | yes | |
| Hydroxide Resistance | limited | |
| Ketone Resistance | yes | |
| Physiological indifference according | no | |
| Resistance Against Hot Water | yes | |
| UV Stabilization | yes |
Users viewing this material also viewed the following:
- S&E Specialty Polymers GA-1941-AFRO PVC
- Global ABS-305 General Purpose ABS
- Lord Adhesives 7542D Two-Component Urethane Adhesive
- ITW Devcon Safety Clear Coatâ„¢ Epoxy, Water Clear
- Teknor Apex MONPRENE® MP 2785H Thermoplastic Elastomer
- SABIC Innovative Plastics Noryl GTX GTX6013 PPE+PA6 (Asia Pacific)
- Loctite® 3565 High performance epoxy, high Tg and low CTE High Tg Underfill
- EMS-Grivory Grivory® XE 4188 nat PA612
- BASF N-Butanol
- BASF Elastollan 1185 A WM TPUR
Copyright © lookpolymers.com All Rights Reserved